Top 10 common forklift mishaps ， forklift operation ought to take note of these matters ！.

Don't undervalue the forklift at the workplace. If the operation is not good, there will be major mishaps in minutes, and there are lots of mishaps including forklifts.

Situation 1: The forklift freight obstructed the motorist's view, and the individual ahead might not be discovered, leading to a rolling mishap.
Case 2: In order to preserve the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the permitted width of the course and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be safe prior to starting.
3. When the forklift begins with a load, the motorist should initially confirm that the tons is stable and trusted.
4. The begin has to be slow and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork expensive when driving. When entering and leaving the task website or while driving, beware that there will certainly be no obstacles in the sky. When the tons is taking a trip, the fork should not be increased too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or cars nearby, the driving signal must be released first. High-speed sharp turns are forbidden. High-speed doglegs will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely restricted to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and need to maintain a specific safety and security range from the lorry ahead. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised other than when stacking or loading. .
8. The height of the lots have to not obstruct the vehicle driver's view. In unique scenarios, when the product affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive securely at a reduced speed when entering the production workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a stabilizing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely fashion, and they will certainly never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between both forks ought to be readjusted as required to make the load of both forks balanced and not manipulated, and one side of the product must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special conditions, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading things, the forklift should be stopped with the brake. .
4. The speed of the automobile ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as feasible under the load, and it must be kept in mind that the fork idea ought to not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be tilted ahead somewhat when the load is reduced to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and harm people. .
8. Straining is banned, and it is prohibited to utilize forks to raise employees to take part in high-altitude procedures to avoid high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or depress the emergency brake switch.
3. The engine is switched off and the power is cut off. (Except for special situations, such as the motorist does not leave the automobile's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be checked, and fuel, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you experience a person before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is enabled.
7. Do not drive across the slope. When the gradient is more than 10%, the car should be driven in reverse when going downhill;.
8. When the forklift workers carry the goods and progress, if they encounter huge or heavy products and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" need to be followed in the Electric Forklift Truck for Warehouse procedure.
1. Single fork Stand-on Electric Pallet Stacker operation is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Auto parking is not allowed under the list below conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844